


The 3126 and 3127 Series Robertshaw® pressure controls are designed as replacements for existing Penn and Robertshaw devices used on air conditioning and refrigeration units.Differentials are calibrated to centers of pressure range of controlDifferentials will decrease slightly at lower end of range and increase slightly at higher end of range


2510261C BORG-WARNER (YORK)

2510261C

O2514742C BORG-WARNER (YORK)

O2514742C




                        The 3030-700 Series Uni-Kits® are designed as universal replacements for virtually all air conditioner controls. The 3030-700 Series is available as universal Uni-Kits or as NO-FUSS direct replacement controls which are shown below. The Uni-Kits provide the greatest possible O.E.M. application replacement coverage with a minimal amount of stock.  The 3030-700 Series Uni-Kits are available in a wide selection of temperature ranges and capillary lengths to fit virtually every replacement application. Select from ambient bulb, straight, or air coil capillary configuration. Uni-Kits include all necessary adaptor mounting brackets, dial shaft adaptors, dial drivers, mounting screws and installation instructions.
                        
                    

25-8799PB BORG-WARNER (YORK)

25-8799PB




                        The Ranco® Dual Pressure Controls combine the functions of a single high-pressure limit control and a single low-pressure control in one unit with a single pole, single throw (SPST) switch.Features and BenefitsConvertible feature allows selection of manual or reset function when operating at high pressure (O12‑4833/O12-4834)A wide range of high-pressure manual or automatic reset controls can be replaced ( or O12‑4834)A high-pressure limit is combined with suction pressure sensing to provide temperature control and/or pump downHigh-limit adjustment screwLow-pressure differential and range adjusting screwsSelector screw for manual or automaticReset buttonLow-pressure scale plateHigh-impact plastic cover with center mount screwHigh-pressure scale plateSuper Cap® capillary protection systemColor-coded for easy identification of pressure lineHigh-side capillary flare nut (silver)Low-side capillary flare nut (brass)Cap included on all Australia temperature controls. Optional for all other regions


25-4326PX BORG-WARNER (YORK)

25-4326PX




                        These controls offer a variety of pressure ranges and switch action to provide maximum application flexibility.Features and BenefitsNEMA 1 enclosure with non-conductive coverFront-located captive cover screwLarge, easy-to-read scale plateSUPER CAP® capillary protection systemUniversal mounting and compact designScrew terminals are raised and fully accessible for easy wiringLaser-welded bellows for extended lifeHeavy-duty plated steel frameSuitable for R12, R22, and R502 applications


O25-05813 BORG-WARNER (YORK)

O25-05813

2512410 BORG-WARNER (YORK)

2512410




                        The Ranco® A22, A30 and 9530 Series Constant Differential Temperature Controls are designed to switch electrical components of refrigeration systems in response to sensed temperatures.Features and BenefitsLaser-welded stainless steel bellowsFixed or adjustable temperature settingsHigh-amperage contactsPneumatic action provided by vapor-filled capillary or capillary with bulb sensing elementsConstant On or Off positions availableChoice of mounting brackets, adjustment ranges and cams, and slotted or flatted shaftsStandard 1/4” quick-connect terminals with optional screw terminals


25-9390 BORG-WARNER (YORK)

25-9390

O25-15265-000 BORG-WARNER (YORK)

O25-15265-000




                        These controls provide extra protection to refrigeration compressors. G20 - Protects against loss of charge or evaporator freeze-up. G23 - Provides high head pressure protection.
                        
                    

25-9011PC BORG-WARNER (YORK)

25-9011PC




The 3433 Gard-Pak II Motor Protector Kits are designed to replace the MP13, MP23 (3423) or MP33 (3433) motor protectors which may have failed, been damaged, or are not operating correctly. The 3433 module is the latest in a series of functionally similar controls and utilizes the most advanced state of the art internal circuitry to rapidly and accurately recognize and react to temperature changes in the stator windings of a motor. The 3433 module utilizes a vibration-resistant enclosed relay which mechanically isolates the solid-state sensing network from the equipment control circuit. This mechanical relay has been used to replace the Triac circuit used in the earlier MP23 (3423) Series. The larger size of this relay necessitates a slightly higher profile on the 3433 than on the MP23. Caution should be exercised to ensure adequate clearance if the 3433 is being used to replace a MP23 module. The 3433 also has a second capacitor to prevent contactor chattering problems. This capacitor also provides protection against momentary "opens" or chatter caused by voltage spikes. The module assembly is bonded in epoxy to ensure that the unit is unaffected by vibration, moisture or other contaminants. The application of a 3433 module requires embedded sensors in the stator windings of a motor. Therefore, these kits can only be used in applications where a Robertshaw® motor protector was part of the original equipment, unless the stator is rewound with new sensors in place.3433-047 Manual reset model requires use of a remote momentary "on" switch (provided by customer) to reset module in the event of an over-temperature condition. Note: The contact resistance and lead resistance of this switch must not exceed 0.15 ohms


O25-20791-003 BORG-WARNER (YORK)

O25-20791-003




                        Adaptable control to replace OEM controls which govern the on/off compressor function. Includes break-off shaft, dial knob, and mounting bracket.
                        
                    

O25-11842-000 BORG-WARNER (YORK)

O25-11842-000

O25-12243-B BORG-WARNER (YORK)

O25-12243-B

25-8073 BORG-WARNER (YORK)

25-8073

25-8087PL BORG-WARNER (YORK)

25-8087PL

25-7545PL BORG-WARNER (YORK)

25-7545PL




                        The Ranco® Wide Range  provide a wide selection of controls customized to allow users exact adjustments within manufacturers' limits. The Ranco O Series features heavy-duty plated steel frames, non-conductive covers with front-located captive cover screws, raised screw terminals for fully accessible wiring, and large easy-to-read scales. Recognizing the need for flexibility in design of refrigeration equipment, these controls offer a wide selection for such products as self-contained refrigerators, freezers, coolers, walk-in units, and refrigeration display cases.Features and BenefitsMaximum adjustment accuracy with 7 revolution range adjustment screwsNEMA 1 enclosure with non-conductive coverUniversal mounting and compact designLaser-welded bellows for extended lifeWide range adjustable differential The O60 Series have these additional features:10 times setting sensitivity of most other wide range controls (O60 series only)Gas-filled, nonposition-sensitive bulb (O60 series only)Cap included on all Australia temperature controls. Optional for all other regions.


25-6807PM BORG-WARNER (YORK)

25-6807PM




The Ranco® O Series Single Low Pressure Controls offer a variety of pressure ranges and switch action to provide maximum application flexibility.Features and BenefitsControls available for most refrigerant typesHigh-amp rated switch (SPST) design (O10-1402/O10-1483)Super Cap® capillary vibration protection systemNon-conductive front cover with captive screwAdjustable differential and rangeEasy-to-read scale plateVibration cone (absorbs and reduces vibration away from brazed joint)Low mass copper alloy capillary tube (reduces capillary stress caused by equipment vibration)The O16-624 control has additional features:Compatible with refrigerants 134A, 401A, 401B, 402A, 402B, 403A, 403B and 404ACap included on all Australia temperature controls. Optional for all other regions


O25-20057C BORG-WARNER (YORK)

O25-20057C

O25-09276-000 BORG-WARNER (YORK)

O25-09276-000




The Ranco® Dual Pressure Controls combine the functions of a single high-pressure limit control and a single low-pressure control in one unit with a single pole, single throw (SPST) switch.Features and BenefitsConvertible feature allows selection of manual or reset function when operating at high pressure (O12‑4833/O12-4834)A wide range of high-pressure manual or automatic reset controls can be replaced (O12-4833 or O12‑4834)A high-pressure limit is combined with suction pressure sensing to provide temperature control and/or pump downHigh-limit adjustment screwLow-pressure differential and range adjusting screwsSelector screw for manual or automaticReset buttonLow-pressure scale plateHigh-impact plastic cover with center mount screwHigh-pressure scale plateSuper Cap® capillary protection systemColor-coded for easy identification of pressure lineHigh-side capillary flare nut (silver)Low-side capillary flare nut (brass)


25-7506PL BORG-WARNER (YORK)

25-7506PL

O25-14518C BORG-WARNER (YORK)

O25-14518C

O25-14029-000 BORG-WARNER (YORK)

O25-14029-000

O25-17178-000 BORG-WARNER (YORK)

O25-17178-000

25-5299PX BORG-WARNER (YORK)

25-5299PX

25-8811PL BORG-WARNER (YORK)

25-8811PL

borg-warner-york - Page 5

Resources

About A2Z

Policies