


                        Robertshaw® DAOP Series 2-wire Rectangular Control Dampers are designed to be used in zone control system applications and for the control of air flow in any duct system. Dampers are designed to work with pressure systems up to 1.2" W.C. All DAOP damper frames are constructed of heavy gauge extruded aluminum with galvanized steel mounting plate. Extruded aluminum blades are attached to a 0.5" diameter octagonal aluminum shaft which are supported by nylon bushings for smooth operation. DAOP dampers are powered by a single stall type motor providing 50 to 75 inch ounces of torque. Minimum blade adjustment is provided by an external locking mechanism. Dampers are spring open/power close and contain a "Lost Motion" breaking system that prevents backlash and shock to the motor gears, bearings and blade shafts when the damper is driven open by the spring return. 


Features and Benefits Standard sizes from 6" x 6" to 36" x 36"Heavy duty extruded aluminum frameNylon bushings for smooth operationAdjustable minimum position2-wire stall type 24 VAC motorDirect coupled actuatorPower consumption of: light-duty E style, 5 watts at 24 VAC; heavy-duty E2 style, 6 watts at 24 VACMotor cover with wiring strain relief insert70 inch ounces of torque


15700 UNI-LINE

15700




                         are used with Safety Valves. To select a replacement, match the factory model number stamped on the pilot to the Uni-Line® order number and check the photo for mounting configuration. Suitable for natural or LP gas using the 0.14 universal orifice.
                        
                    

28191 UNI-LINE

28191




The Ranco® P30 Series Lube Oil Protection Controls guard pressure-lubricated refrigeration compressors against major damage due to loss of oil pressure. This control utilizes the built-in P30 Time Delay Switch to start timing when oil pressure drops below operating requirements. The timer is designed not only to track oil pressure recovery within a set period, but also to alert the control circuit to open and stop the compressor when the recovery period is exceeded. These controls also feature replaceable time delay modules, Super Cap® capillary protection system and front-located captive cover screw.Features and BenefitsAlarm circuit standardAmbient temperature compensatedSuper Cap® capillary protection systemHigh impact, non-conductive coverField replaceable switch moduleManual resetIndustry standard circuitry and terminal identification


92299 UNI-LINE

92299




Please use model 5300-514 as a replacement.The Robertshaw® 5300 Series Electric Thermostat is a snap-acting, single pole single throw (SPST) type thermostat. Most thermostats use silver contacts and have heavy-duty terminals for durability and sustained accuracy. The snapaction mechanism is precise and reliable. This direct acting series of thermostats is suitable for the commercial cooking industry.
Features and BenefitsKN models are NAK filled diastats with temperature ranges up to 975°F (524°C)Rugged and compact design for versatility and long lifeBulb and capillary available in copper, nickel plated copper and stainless steel (most models)Plastic coating available for protection against moisture, dust, etc. (most models)Dials of heat resistant plastic availableRX millivolt models with hermetically sealed reed switchStem flat in down positionAmbient temperature 200°F (93°C)


24009 UNI-LINE

24009




                        Robertshaw® DAOP Series 3-Wire Rectangular Control Dampers are designed to be used in zone control system applications and for the control of air flow in any duct system. Dampers are designed to work with pressure systems up to 1.2" W.C. All DAOP 3-Wire damper frames are constructed of heavy gauge extruded aluminum with galvanized steel mounting plate. Extruded aluminum blades are attached to .5" diameter octagonal steel shafts which are supported by nylon bushings for smooth operation. DAOP 3-wire dampers are powered by a double stacked stall type motor providing 55 inch ounces of torque. Minimum blade adjustment is provided by an external locking mechanism.Features and Benefits Standard sizes from 6" x 6" to 36" x 36"Heavy duty extruded aluminum frameNylon bushings for smooth operationAdjustable minimum position3-wire stacked stall type 24 VAC motorDirect coupled actuatorPower consumption is 4 watts at 24 VACBlade rotation is 90 degrees55 inch ounces of torque in 35 seconds


15738 UNI-LINE

15738




                        The Slip-Fit® Knobs are designed to be used in conjunction with the dial overlays and 4-way insert adaptors. These three versatile parts enable the installer to quickly replace most O.E.M. knobs encountered in everyday service work.
                        
                    

28150 UNI-LINE

28150

15935 UNI-LINE

15935




                        Robertshaw® DAOP Series 2-wire Rectangular Control Dampers are designed to be used in zone control system applications and for the control of air flow in any duct system. Dampers are designed to work with pressure systems up to 1.2" W.C. All DAOP damper frames are constructed of heavy gauge extruded aluminum with galvanized steel mounting plate. Extruded aluminum blades are attached to a 0.5" diameter octagonal aluminum shaft which are supported by nylon bushings for smooth operation. DAOP dampers are powered by a single stall type motor providing 50 to 75 inch ounces of torque. Minimum blade adjustment is provided by an external locking mechanism. Dampers are spring open/power close and contain a "Lost Motion" breaking system that prevents backlash and shock to the motor gears, bearings and blade shafts when the damper is driven open by the spring return.
Features and Benefits 
• Standard sizes from 6" x 6" to 36" x 36"
• Heavy duty extruded aluminum frame
• Nylon bushings for smooth operation
• Adjustable minimum position
• 2-wire stall type 24 VAC motor
• Direct coupled actuator
• Power consumption of: light-duty E style, 5 watts at 24 VAC; heavy-duty E2 style, 6 watts at 24 VAC
• Motor cover with wiring strain relief insert
• 70 inch ounces of torque
                        
                    

16958 UNI-LINE

16958




The NO-FUSS direct replacement 3030-100 series of cold controls are made by Robertshaw®, one of the world's largest manufacturers of cold controls. They are designed as exact replacements for the original O.E.M. controls. With the same temperature specifications, dial shaft, capillary length, and mounting as the original control, there is no guesswork - just simple installation. The NO-FUSS direct replacements are the largest selection of direct replacement cold controls available today... from one source - Robertshaw.Individually boxed in a strong corrugated carton for extra protection from damage during handling or shippingComplete label information - O.E.M. name and O.E.M. part numbers for handy referenceDetailed instructions for trouble-free installationU.L. and C.S.A. listed


92150 UNI-LINE

92150




                        These kits are ideally suited for use with refrigerators that have automatic icemakers or water dispensers. Each kit comes with all the parts necessary for a complete installation. These kits are ideally suited for use with refrigerators that have automatic icemakers or water dispensers. Each kit comes with all the parts necessary for a complete installation. Econo Kit 1/4" compression union/saddle valve.
                        
                    

77689 UNI-LINE

77689




                        The 4030 Series is the same as the 4020 Series except they have a pilot outlet only. Pilot gas is supplied through a drilled passageway to the pilot valve chamber and outlet. Pilot outlet is 1/4" tubing. If unable to determine a replacement from the ordering chart, note the factory part number ("Z" number) ink-stamped on the control and contact your Uni-Line wholesaler. 100,000 BTU/HR. capacity. Ambient Temperature 32° - 350°F.
                        
                    

35172 UNI-LINE

35172




                        The Robertshaw® 5300 Series Electric Thermostat is a snap-acting, single pole single throw (SPST) type thermostat. Most thermostats use silver contacts and have heavy-duty terminals for durability and sustained accuracy. The snapaction mechanism is precise and reliable. This direct acting series of thermostats is suitable for the commercial cooking industry.
Features and Benefits

KN models are NAK filled diastats with temperature ranges up to 975°F (524°C)Rugged and compact design for versatility and long lifeBulb and capillary available in copper, nickel plated copper and stainless steel (most models)Plastic coating available for protection against moisture, dust, etc. (most models)Dials of heat resistant plastic availableRX millivolt models with hermetically sealed reed switchStem flat in down positionAmbient temperature 200°F (93°C)


24187 UNI-LINE

24187

DA3420E3 UNI-LINE

DA3420E3




                        Robertshaw® water heating elements are made only of high quality material and are assembled by state-of-the-art computer-controlled, automated equipment. 100% computerized testing of critical electrical parameters insures that every element that leaves our factory has met the highest standards of the industry. Standard features include plated steel mounts, terminal caps stamped with watts and volts and a plated copper sheath element with repressed bends for maximum electrical integrity. U.L. listed, C.S.A. approved. Available individually bagged with gasket or in bulk packs of 50 pieces with a matching number of gaskets included.
                        
                    

66081 UNI-LINE

66081




                        The Robertshaw® 5210 Series Electric Thermostat is a direct acting, single pole, slow make and break type thermostat. Typical applications are for incubators, laboratory ovens, water baths, sterilizers, dishwashers, steam tables, scalding tanks and other equipment where a close temperature differential is required.
Features and Benefits

Temperature ranges to 550°F (288°C)Single pole, slow make and break designVery sensitive to temperature changeSmall temperature differential between make and breakFine silver contacts to assure consistent switch action and long lifeRugged and compact design for versatility of applicationBulb and capillary available in copper or nickel plated copper


23193 UNI-LINE

23193

16009 UNI-LINE

16009




                        The Robertshaw® aluminum tubing is versatile for all your replacement needs. It comes in a full range of sizes in 50 foot and 5 foot lengths.Features and BenefitsAluminum tubing meets ASTMB Standard #483Uses a 1435 alloy with a 0.035" wall thicknessTubing is rated at 90 PSI with an 11,000 tensile, 9500 yield and a 25% elongation


ALT18 UNI-LINE

ALT18




                        The 3030-400 Series Uni-Kits® feature a constant cut-in at 39°F. This constant cut-in on every cycle provides automatic defrost while maintaining food temperature at a safe level. Turning the dial will change the differential between the cut-in and cut-out temperatures, with cut-in always remaining fixed at 39°F. The 3030-400 Series Uni-Kits are available in a wide selection of temperature ranges and capillary lengths to fit virtually every replacement application. Uni-Kits include all necessary adaptor mounting brackets, dial shaft adaptors, dial drivers, mounting screws and installation instructions.Features and Benefits Individually boxed in a strong corrugated carton for extra protection from damage during handling or shippingComplete label information - O.E.M. name and O.E.M. part numbers for handy referenceDetailed instructions for trouble-free installationU.L. and C.S.A. listed


77633 UNI-LINE

77633

35169 UNI-LINE

35169




Robertshaw® DAR Series Round Control Dampers are designed to be used in zone control system applications and for the control of air flow in any duct system. Dampers are designed to work with pressure systems up to 1.2" W.C. All DAR damper shells are constructed of rolled 26 gauge galvanized steel with stiffening ribs to maintain rigidity. A single 18 gauge offset blade is attached to a .375" one-piece steel shaft which is attached to nylon bearings for smooth operation. DAR dampers are powered by a single stall type motor providing 55 to 75 inch ounces of torque. Motor mounts are welded to the damper shell. Minimum blade adjustment is provided by an external locking mechanism. Dampers are spring open/power close and contain a “Lost Motion” braking system that prevents backlash and shock to the motor gears, bearings and blade shaft when the damper is driven open by the spring return. Damper size will vary based on system static pressure. Refer to duct calculator for proper sizing.
Features and Benefits Sizes from 5" to 20" diametersHeavy duty reinforced galvanized steel shellMotor mount welded to shell18 gauge offset bladeNylon bearings for smooth operation2-wire stall type 24 VAC motorDirect coupled actuatorPower consumption of: light-duty E style, 5 watts at 24 VAC; heavy-duty E2 style, 6 watts at 24 VACMotor cover with wiring strain relief insert


16444 UNI-LINE

16444




                        Robertshaw® DAOP Series 2-wire Rectangular Control Dampers are designed to be used in zone control system applications and for the control of air flow in any duct system. Dampers are designed to work with pressure systems up to 1.2" W.C. All DAOP damper frames are constructed of heavy gauge extruded aluminum with galvanized steel mounting plate. Extruded aluminum blades are attached to a 0.5" diameter octagonal aluminum shaft which are supported by nylon bushings for smooth operation. DAOP dampers are powered by a single stall type motor providing 50 to 75 inch ounces of torque. Minimum blade adjustment is provided by an external locking mechanism. Dampers are spring open/power close and contain a "Lost Motion" breaking system that prevents backlash and shock to the motor gears, bearings and blade shafts when the damper is driven open by the spring return.Features and Benefits Standard sizes from 6" x 6" to 36" x 36"Heavy duty extruded aluminum frameNylon bushings for smooth operationAdjustable minimum position2-wire stall type 24 VAC motorDirect coupled actuatorPower consumption of: light-duty E style, 5 watts at 24 VAC; heavy-duty E2 style, 6 watts at 24 VACMotor cover with wiring strain relief insert70 inch ounces of torque


16209 UNI-LINE

16209




                        These heavy duty 15 amp Paragon® timers are being used by the OEM manufacturers today. They will replace both the older classic design timers and the new OEM versions. Must be ordered in multiples of 12.
                        
                    

77951 UNI-LINE

77951




                        These controls provide extra protection to refrigeration compressors. G20 - Protects against loss of charge or evaporator freeze-up. G23 - Provides high head pressure protection.
                        
                    

92130 UNI-LINE

92130




                        The Robertshaw® 4350 Series Gas Thermostat is a combination gas cock and by-pass type thermostat. It is available with both by-pass and pilot adjustments. With these thermostats, the gas is turned on and the temperature setting made with a single turn of the dial. The 4350 Series is available for a wide variety of applications, especially ranges and griddles.
Features and Benefits

Highly adaptable because of multiple orientations and number of outletsMounted, via flange nipple, above or below the manifoldAvailable with various temperature rangesFront adjustment for pilot and by-passModulating seat actionBulb and capillary available in copper, nickel plated copper and stainless steel


uni-line - Page 296

Resources

About A2Z

Policies